notes: 1. all dimensions are in millimeters (inches); 2. tolerances are 0.1mm (0.004inch) unless otherwise noted. 3. polarity referring onto the cathode mark is reversed on the red. a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps 5630 package power white surface mount device part number: 62-217buw1c2 package outlines & re-flow profile ? soldering iron basic spec is u 5sec when 260 . if temperature is higher, time should be shorter (+10 ? -1sec ).power dissipation of iron should be smaller than 15w, and temperatures should be controllable .surface temperature of the device should be under 230 . ? reflow temp/time item materials resin (mold) epoxy lens color yellow diffused printed circuit board bt emitted color white material ingan
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 electro-optical characteristics (t a =25 ) value parameter test condition symbol min. typ. max. unit viewing angle at 50% i v i f =150ma 2 1/2 120 deg forward voltage i f =150ma v f 2.8 --- 3.5 v 5250 5750 6250 color temperature i f =150ma cct 3750 4000 4250 k --- 54 --- luminous flux i f =150ma flux --- 56 --- lm pulse forward current (pulse width 10msec, and duty 1/10) i fp 300 ma absolute maximum ratings (t a =25 ) parameter symbol value unit forward current i f 150 ma reverse voltage v r 5 v reverse current i r 1 a power dissipation p d 585 mw operating temperature range top -30 ~+80 storage temperature range tstg -40 ~+85
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 bin code
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 color rank
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 cie chromaticity diagram
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 typical electro-optical characteristic curves
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2 packaging tape, reel, and packing model
precautions for use 1. over-current proof customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (burn out will happen). 2. storage 2.1 do not open moisture proof bag befo re the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 70%rh or less. 2.5 the leds should be used within 168 hour s (7 days) after opening the package. 2.6 if the moisture absorbent material (silica ge l) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment U 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board. 4. soldering iron each terminal is to go to the tip of soldering iron temper ature less than 280 for 3 seconds within once in less than soldering ir on capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. surface mount led lamps part number: 62-217buw1c2
|
